Now showing items 1-7 of 7

    • Bimodal grain microstructure development during hot compression of a cast-homogenized Mg-Zn-Zr alloy 

      Hadadzadeh, Amir; Mokdad, Fatma; Shalchi Amirkhiz, Babak; Wells, Mary; Williams, Bruce W.; Chen, Daolun L. (Elsevier, 2018-05-02)
      Hot deformation of a cast-homogenized ZK60 alloy was studied by compression at a temperature of 450 °C and a strain rate of 0.001 s−1 to investigate microstructural evolution. The deformed microstructure was characterized ...
    • Effect of alloy composition on hot deformation behavior of some Al-Mg-Si alloys 

      ODOH, DANIEL OGHENEKEWHE; Mahmoodkhani, Yahya; Wells, Mary (Elsevier, 2018-03-01)
      The hot flow stress behavior of three Al-Mg-Si alloys was determined by performing hot deformation compression tests on a Gleeble 3500 thermomechanical simulator over the temperature range 400 °C–550 °C and at strain rates ...
    • Low-cycle fatigue characterization and texture induced ratcheting behaviour of forged AZ80 Mg alloys 

      Gryguc, Andrew; Behravesh, Seyed Behzad; Shaha, Sugrib K.; Jahed, Hamid; Wells, Mary; Williams, Bruce W.; Su, Xuming (Elsevier, 2018-11-01)
      Stress-controlled uniaxial “push-pull” fatigue testing was conducted on as-received (cast and extruded) and closed-die cast-forged and extruded-forged AZ80 Mg alloy. The as-cast material possessed random texture and somewhat ...
    • Mathematical modeling of thermo-mechanical behavior of strip during twin roll casting of an AZ31 magnesium alloy 

      Hadadzadeh, Amir; Wells, Mary (Elsevier, 2013-06-01)
      The effect of set-back distance on the thermo-mechanical behavior of the strip during twin roll casting (TRC) of an AZ31 magnesium alloy was modeled using finite element method (FEM). Model validation was done by comparing ...
    • Monotonic and cyclic behaviour of cast and cast-forged AZ80 Mg 

      Gryguc, Andrew; Shaha, Sugrib K.; Behravesh, Seyed Behzad; Jahed, Hamid; Wells, Mary; Williams, Bruce W.; Su, X. (Elsevier, 2017-11)
      Tensile and strain-controlled fatigue tests were performed to investigate the influence of forging on the performance of cast AZ80 magnesium alloy. The obtained microstructural analysis showed that the as-cast AZ80 magnesium ...
    • Process parameters for hot stamping of AA7075 and D-7xxx to achieve high performance aged products 

      Omer, Kaab; Abolhasani, Atekeh; Kim, Samuel; Nikdejad, Tirdad; Butcher, Clifford; Wells, Mary; Esmaeili, Shahrzad; Worswick, Michael (Elsevier, 2018-07)
      This work examines the necessary process parameters for die quenching (DQ) during hot stamping and subsequent age hardening and paint bake cycle (PBC) response for two alloys: AA7075 and a developmental 7xxx alloy (referred ...
    • Sagging resistance of warm formed aluminum brazing sheet 

      Benoit, Michael J.; Kaur, R.; Wells, Mary; Jin, H.; Amirkhiz, B. Shalchi; Winkler, Sooky (Elsevier, 2018-04-01)
      Interrupted tensile tests, performed between room temperature (RT) and 250°C, were used to simulate warm forming of an AA3003/AA4045 brazing sheet. Brazing performance was predicted from sagging distance measurements after ...

      UWSpace

      University of Waterloo Library
      200 University Avenue West
      Waterloo, Ontario, Canada N2L 3G1
      519 888 4883

      All items in UWSpace are protected by copyright, with all rights reserved.

      DSpace software

      Service outages